A Company of Interna Group

TRADITIONAL TRANSITIONAL CONTEMPORARY

Upholstery and Chairs

FRAMES

Visible wooden parts are made of solid wood with finishes and types of wood as specifically indicated in this catalogue for each model. Frames are made of solid wood, plywood or fibre panels, reinforced and glued. Seat bases are made of plywood boards and/or elastic straps.

UPHOLSTERY

Upholstery padding is made of flame-retardant variable density foam, which conform to standards in force in the country of destination. Resinates such as Valform are used in some models

FABRICS/LEATHERS

Fabrics and leathers can be supplied by the customer or selected from Interna Fabric Collection. In case of C.O.M. fabrics, the requirements are shown without repeat and with a width of 140 cm/ 55 in. Fabrics of different widths or with repeat are calculated on a one-off basis. Leather requirements are given in sq. meters/sq. feet. Quantities of special or small size leather are calculated on a one-off-basis.  On request, items can be upholstered with a combination of various fabrics and/or leathers. In this case the calculations will again be made on a one-off basis. Interna own catalogue presents four  fabric and one leather price categories. All leathers and fabrics belonging to Interna fabric collection are Trevira CS and therefore comply with the major European fire retardant requirements and are adequate for hospitality use. In case of selection of two or more fabrics/leathers from different categories, the price considered will always be the one of the higher category.

FINIALS

Finials are made of metal with finishes as specifically indicated in this catalogue for each model.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is done with polyurethane or acrylic resins, depending on the type of wood and veneers used. On demand, and when technically feasible, fire-retardant  varnishing which satisfies the laws and standards in force  in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

Tables

STRUCTURE

Table bases and columns are made of metal or solid wood as specifically indicated in this catalogue for each model. Table tops are made of solid wood, metal, glass or C.O.M. leather as specifically indicated in this catalogue for each model. Veneered tops with finishes and woods as specifically indicated in this catalogue for each model are made of wood-base panels according to standards UNI EN 717 and EN 120/95, class E1. Panels are not fire-retardant or water-proof unless this is requested by the client.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing of table tops is carried out with UV, polyurethane or acrylic resins, depending on the type of woods and veneers used. Varnishing of table bases and columns is performed with polyurethane or acrylic resins. On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

NOTE ON USE

The tables with wood top, lacquer or varnished, due to the nature of wood, can be damaged by direct contact with warm sources. On demand, Interna can supply glass tops as protection for the wood or tops made of high pressure laminate.

Casegoods

STRUCTURE

Structures of casegoods are made of wood-base panels according to standards UNI EN 717 and EN 120/95, class E1. Panels are veneered with finishes and woods as specifically indicated in this catalogue for each model. Panels are not fire-retardant or water-proof unless this is requested by the client. Drawers are made of plywood with the same finish as for the piece of furniture to which they refer to and are installed on metal 3/4 - extension concealed runners . On demand drawers can be installed on full extension runners. Marble and granite tops have a polished finish.

HINGES

Hinges are made of nickel-plated steel.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is made with polyurethane or acrylic resins, depending on type of woods and veneers to be used. On demand and when technically feasible fire-retardant varnishing according to laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

NOTE ON USE

The marble tops can be stained if placed in direct contact with acid substances. On demand, Interna can supply a protective treatment. The protective treatment, due to the nature of the marble, must be renewed in time.

LES GRANDES CLASSIQUES DE JACQUES GARCIA

Upholstery and Chairs

WOOD FINISHES

Wooden parts are made of solid beechwood and are available in the following glossy finishes: stained mahogany and black lacquer.

UPHOLSTERY

Upholstery padding is made of flame-retardant variable density foam, which conforms to standards in force in the country of destination. Resinates such as Valform are used in some models.

FABRICS/LEATHERS/TRIMMINGS

Fabrics and leathers can be supplied by the customer or selected from Interna Fabric Collection. In case of C.O.M. fabrics, the requirements are shown without repeat and with a width of 140 cm/ 55 in. Fabrics of different widths or with repeat are calculated on a one-off basis. Leather requirements are given in sq. meters/sq. feet. Quantities of special or small size leather are calculated on a one-off-basis. On request, items can be upholstered with a combination of various fabrics, trimmings and/or leathers. In this case the calculations will again be made on a one-off basis. Interna own catalogue presents four  fabric and one leather price categories. All leathers and fabrics belonging to Interna fabric collection are Trevira CS and therefore comply with the major European fire retardant requirements and are adequate for hospitality use.In case of selection of two or more fabrics/leathers from different categories, the price considered will always be the one of the higher category.When the upholstered item requires trimmings, the cost of the trimmings is already included in the fabric price categories.

NAILS AND FINIALS

The nails are supplied with an antique gold finish. The finials are made of cast brass with a satin finish.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is done with polyurethane resins. On demand and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerance.

Casegoods and Tables

WOODEN FINISHES

All items are available with the following finishes:
- mahogany veneer, beechwood stained mahogany;
- MDF and beechwood with a black lacquer finish;
- HPL (high pressure laminate) in mahogany and in polished or mat black lacquer finish.

NAILS AND FINIALS

The nails are supplied with an antique gold finish. The finials are made of cast brass with a satin finish.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is done with polyurethane resins. On demand and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerance.

Outdoor furniture

FRAME

The table and chair frames are made of steel with cataphoresis coating.

PADDING

Padding is made of outdoor waterproof mildew-resistant foam.

GLIDES

Glides are made of nylon.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerance.

NOTE ON USE

The tables with wood top, lacquer or varnished, due to the nature of wood, can be damaged by direct contact with warm sources. On demand, Interna can supply glass tops as protection for the wood. The tables with marble tops can be stained if placed in direct contact with acid substances. On demand, Interna can supply a protective treatment. The protective treatment, due to the nature of the marble, must be renewed in time.

ANGLODUTCH BY FG STIJL

Upholstery and Chairs

FRAMES

Visible wooden parts are made of solid wood with finishes and types of wood as specifically indicated in this price list for each model. Frames are made of solid wood, plywood or fibre panels, reinforced and glued. Seat bases are made of plywood boards and/or belts.

UPHOLSTERY

Upholstery padding is made of flame-retardant variable density foam, which conforms to standards in force in the country of destination. Resinates such as Valform are used in some models.

FABRICS/LEATHERS

Fabrics and leathers can be supplied by the customer or selected from Interna Fabric Collection. In case of C.O.M. fabrics, the requirements are shown without repeat and with a width of 140 cm/ 55 in. Fabrics of different widths or with repeat are calculated on a one-off basis. Leather requirements are given in sq. meters/sq. feet. Quantities of special or small size leather are calculated on a one-off-basis.  On request, items can be upholstered with a combination of various fabrics and/or leathers. In this case the calculations will again be made on a one-off basis. Interna own catalogue presents four  fabric and one leather price categories. All leathers and fabrics belonging to Interna fabric collection are Trevira CS and therefore comply with the major European fire retardant requirements and are adequate for hospitality use. In case of selection of two or more fabrics/leathers from different categories, the price considered will always be the one of the higher category.

FINIALS

Finials are made of metal with finishes as specifically indicated in this price list for each model.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is done with polyurethane or acrylic resins, depending on the type of wood and veneers used. On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

Tables

FRAME

Table bases and columns are made of metal or solid wood as specifically indicated in this price list for each model. Table tops are made of solid wood and marble as specifically indicated in this price list for each model or with glass protection if specifically requested. Veneered tops with finishes and woods as specifically indicated in this price list for each model are made of wood-based panels according to standards UNI EN 717 and EN 120/95, class E1. Panels are not fire-retardant or water-proof unless this is requested by the client.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing of table tops is carried out with UV, polyurethane or acrylic resins, depending on the type of woods and veneers used. Varnishing of table bases and columns is performed with polyurethane or acrylic resins. On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

NOTE ON USE

The tables with wood top, lacquered or varnished, due to the nature of wood, can be damaged by direct contact with warm sources. On demand, Interna can supply glass tops as protection for the wood or tops made of high pressure laminate. The tables with marble tops can be stained if placed in direct contact with acid substances. On demand, Interna can supply a protective treatment. The protective treatment, due to the nature of the marble, must be renewed in time.

Casegoods

STRUCTURE

Structures of casegoods are made of fibre panels according to standards UNI EN 717 and EN 120/95, class E1. Panels are veneered with finishes and woods as specifically indicated in this price list for each model. Panels are not fire-retardant or water-proof unless this is requested by the client. Drawers are made of plywood with the same finish as for the piece of furniture to which they refer to and are installed on metal  extension concealed runners. On demand drawers can be installed on full extension runners. Marble tops have a polished finish.

HINGES

Hinges are made of nickel-plated steel.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is made with polyurethane or acrylic resins, depending on type of woods and veneers to be used. On demand and when technically feasible fire-retardant varnishing according to laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

Outdoor Tables

FRAME

Table bases are made of steel and lined with satin stainless steel. The columns are made of powder coated steel or aluminum, covered with Burma teak veneered marine plywood. Columns are available with fix height or with adjustable height by a gas spring. The tops are made of solid Burma or Iroko teak.

GLIDES

Glides are made of nylon or felt.

FINISH OF THE WOOD PARTS

The finish of the wood parts is implemented by impregnation in vegetal base oil.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

Sun Beds

FRAME

The frames are made of solid teak treated appropriately. The seating supports are made of teak staves.
The sunshades frames are made of steel welded elements with metal counterweights to avoid overturning in the event of strong wind.

PADDING

Padding is made of outdoor waterproof mildew-resistant foam.

FABRICS

Fabrics can be supplied by the customer or selected from Interna Fabric Collection. Fabric requirements are shown without repeat and with a width of 140 cm/ 55 in. Fabrics of different widths or with repeat are calculated on a one-off basis. On request, items can be upholstered with a combination of various fabrics. In this case the calculations will again be made on a one-off basis.

GLIDES

Glides are made of nylon.

FINISH OF THE WOOD PARTS

The finish of the wood parts is implemented by impregnation in vegetal base oil.

VARNISH OF THE WELDED PARTS

Coating is carried out with epoxy powders for outdoor purposes.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

BEDROOM STORIES

Headboards

FRAME

The external wood parts of the five rooms are made  of solid and veneered wood and comply with the UNI EN 309 and EN 120/95 class E1 ruling. The internal panels are  made of fibre and solid wood. Panels are not fire-retardant or water-proof unless this is requested by the client. 

UPHOLSTERY

Volupté: structure upholstery is made with foam and technical fire-retardant stain repellent fabric, in compliance with the regulations of the country of destination. Harmony/Poetry/Morpheus: structure  upholstery is made with technical fire-retardant stain repellent fabric or leather/hide in compliance with the regulations of the country of destination.

VARNISHING AND LACQUERING

Varnishing is carried out with UV, polyurethane or acrylic resins or with epoxy powders. On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

ELECTRIFICATION SYSTEM

The headboards are supplied with cabling as far as the decorative light are concerned but without electric sockets and without reading lamps. Electrification system can be supplied on demand and will comply with the regulations of the country of destination.

Casegoods

STRUCTURE

Structures are made of fibre panels according to standards UNI EN 309 and EN 120/95, class E1. Panels are veneered with finishes and woods as specifically indicated  for each model. Panels are not fire-retardant  or water-proof unless this is requested by the client. Drawers, were foreseen, are made of plywood with the same finish as for the piece of furniture to which they  refer to and are installed on metal  extension concealed runners. On demand drawers can be installed on full extension runners. Marble tops have a polished finish.

HINGES

Hinges are made of metal with a nickel finish.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is made with polyurethane or acrylic resins, depending on the  type of woods and veneers to be used. On demand and when technically feasible fire-retardant varnishing according to laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

ELECTRIFICATION SYSTEM

The furniture is supplied without electrification system, and when requested  it will have to be agreed upon  on a one-off basis for each single supply and will comply  with the regulations of the country of destination.

EQUIPMENTS

The minibar do not include the fridge and will be customized  as per the model of the minibar selected by the client.

Tables - Small Tables

FRAME

Table bases and columns are made of  metal or solid wood as specifically indicated for each model.  Table tops are made of solid wood  veneered or lacquer, marble or resin as specifically indicated  for each model. A glass protection will be supplied on demand. Veneered tops with finishes and woods as specifically  indicated for each model are made of fibre panels according to standards UNI EN 309 and EN 120/95, class E1. Panels are not fire-retardant or water-proof unless this is requested by the client.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing of table tops is carried out with UV, polyurethane or acrylic resins, depending on the type of woods and veneers used. Varnishing of table bases and columns is performed with polyurethane or acrylic resins or powder varnishes. On demand, and when  technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

Upholstery and Chairs

FRAME

Visible wooden parts are made of solid wood with finishes and types of wood as specifically indicated for each model. Internal frames are made of solid wood, plywood or fibre panels, reinforced and glued. Seat bases are made of plywood boards and/or elastic belts.

UPHOLSTERY

Upholstery padding is made of Olmo type flame-retardant variable density foam, in any case complying to the standards in force in the country of destination. Resinates such as Valform are used in some models.

FABRICS/LEATHERS

Fabrics and leathers can be supplied by the customer or selected from Interna Fabric Collection. In case of C.O.M. fabrics, the requirements are shown without repeat and with a width of 140 cm/ 55 in. Fabrics of different widths or with repeat are calculated on a one-off basis. Leather requirements are given in sq. meters/sq. feet. Quantities of special or small size leather are calculated on a one-off-basis. On request, items can be upholstered with a combination of various fabrics and/or leathers. In this case the calculations will again be made on a one-off basis. Interna own catalogue presents four  fabric and one leather price categories. All leathers and fabrics belonging to Interna fabric collection are Trevira CS and therefore comply with the major European fire retardant requirements and are adequate for hospitality use.In case of selection of two or more fabrics/leathers from different categories, the price considered will always be the one of the higher category.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is done with polyurethane or acrylic resins, depending on the type of wood and veneers used.  On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres  and inches and are subject to normal tolerances.

Lamps

Lamps are supplied with certifications that comply with  the regulations of the country of destination.  They are customizable in materials and finishes and can  be adapted for each of the five rooms.

ECHOES BY KHUAN CHEW

Upholstery and Chairs

FRAMES

Visible wooden parts are made of solid wood with finish and type of wood as specifically indicated in this catalogue for each model. Internal frames are made of solid wood, plywood or fibre panels, reinforced and glued. Seat bases are made of plywood boards and/or elastic belts.

UPHOLSTERY

Upholstery padding is made of flame-retardant variable density foam, in compliance with the standards in force in the country of destination. Resins such as Valform are used in some models.

FABRICS/LEATHERS

Fabrics and leathers can be supplied by the customer or selected from Interna Fabric Collection. In case of C.O.M. fabrics, the requirements are shown without repeat and with a width of 140 cm/ 55 in. Fabrics of different widths or with repeat are calculated on a one-off basis. Leather requirements are given in sq. meters/sq. feet. Quantities of special or small size leather are calculated on a one-off-basis. On request, items can be upholstered with a combination of various fabrics and/or leathers. In this case the calculations will again be made on a one-off basis. Interna own catalogue presents four  fabric and one leather price categories. All leathers and fabrics belonging to Interna fabric collection are Trevira CS and therefore comply with the major European fire retardant requirements and are adequate for hospitality use.In case of selection of two or more fabrics/leathers from different categories, the price considered will always be the one of the higher category.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing is done with polyurethane or acrylic resins, depending on the type of material used. On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

Tables and complements

STRUCTURES

Bases and structures, are made of metal or fibre panels according to standards UNI EN 309 and EN 120/95, class E1 as specifically indicated for each model. Table tops are made of wood, metal, glass or C.O.M. leather as specifically indicated for each model. Veneered tops, with finish and type of wood as specifically indicated in this catalogue for each model, are made of fibre panels according to standards UNI EN 309 and EN 120/95, class E1. Panels are not fire-retardant or water-proof unless specifically requested by the client.

GLIDES

Glides are made of nylon or, on demand, metal or felt.

VARNISHING AND LACQUERING

Varnishing of table tops is carried out with UV, polyurethane or acrylic resins, depending on the type of material used. Varnishing of bases and structures is performed with polyurethane or acrylic resins. On demand, and when technically feasible, fire-retardant varnishing which satisfies the laws and standards in force in the country of destination may be performed.

SIZES

The dimensions of all products stated in the technical specifications are given in centimetres and inches and are subject to normal tolerances.

COLLECTION PRÉSIDENT by Bruno Moinard

ORBINE ARMCHAIR

Armchair with a solid oakwood base with plywood panels covered with polyurethane expanded foam. Back and seat are padded with flexible foam with different densities.

SOLARI SOFA

Series of sofas with two lengths, made of plywood panels covered with polyurethane expanded foam. The seat is padded with flexible foam with a special top level made of a viscous-elastic foam. The back cushions are made of flexible foam and goose feathers. The feet have a varnished bronze finish.

BORGEO  WORKING TABLES

Series of rectangular and bean shaped tables with veneered fibreboard top and steel base. The tops are made of honeycomb boards with a millerays veneer with irregular vein. The two veneers and finishes available are: light grey bleached oakwood with a mat transparent coat and dark grey oakwood with a 100 gloss finish. The drawer, with leather bottom, is mounted on metal full extension slides with dampers or on revolving ball bearing ones. The base is made of galvanized hexagonal tube with a brushed bronze finish; the legs have adjustable feet.

LURI MEETING TABLES

Series of rectangular and bean shaped tables with great dimensions with veneered fibreboard top, a metal frame and a wooden base that can be wired. The tops are made of honeycomb boards with a millerays veneer with irregular vein. The two veneers and finishes available are: light grey bleached oakwood with a mat transparent coat and dark grey oakwood with a 100 gloss finish. The tops are equipped with a cable port with a flush door with the same finish as the top. The wooden base is equipped with a door to allow an easy access to the wiring. The metal structure is made of galvanized hexagonal tube with a brushed bronze finish; the legs have adjustable feet.

PENTA COFFEE TABLES

Series of rectangular and bean shaped coffee tables with veneered fibreboard top and metal base. The tops are made of honeycomb boards with a 3D striped and brushed veneer with irregular vein. The two veneers and finishes available are: brushed bleached conifer wood with mat transparent coat and brushed dark grey oakwood with a 100 gloss finish. The base is made of two paired galvanized rectangular sections with brushed bronze and polished nickel finish.

FIGARO SIDE UNIT

Side unit for the working table, with a frame made of veneered fibreboard and a curved shutter made of plywood. The two veneers and finishes available are: light grey bleached oakwood with a mat transparent coat and dark grey oakwood with a 100 gloss finish. Decorative profiles and handles are made of galvanized steel with a brushed bronze finish. The unit is equipped with a  lower drawer with a leather front, middle drawer with a wooden veneered front and a leather pull-out tray. The unit is supplied ready for cabling that is not included.

LECCIE COFFER

Container unit with a frame made of veneered fibreboard and a curved shutter made of plywood upholstered in leather with pull-out tray with dividers upholstered in leather. The two veneers and finishes available are: brushed bleached conifer wood or dark grey oakwood with a mat transparent coat. Feet, decorative profiles and handles are made of galvanized steel with a brushed bronze finish.

LEVI CONSOLE

Rectangular console with two glass shelves and steel structure. The shelves are made of a12 mm back painted extra clear glass with a brushed finish on the top. The structure is made of galvanized section bars with a brushed bronze and polished nickel finish.

CALVIE CREDENZA

Multifunction container unit with a frame made of fibreboard veneered or upholstered in leather. The two veneers and finishes available are: brushed bleached conifer wood or dark grey oakwood with a mat transparent coat. The unit is composed by a deeper section with double doors with a leather groove and by a side unit made of two identical parts, one being a rotating storage-door upholstered in leather with a 180° opening and holder in brushed bronze finish.
Internally the unit is completely upholstered in leather, with a curved back and build-in led lights and lighting sensor on the middle shelf.
The credenza is supplied fully cabled.

CORTI SCREEN

Double faced screen with a solid wood structure and inserts made of a translucent banana tree fibre fabric and hidden hinges with bronze finish.
The two veneers and finishes available are: brushed bleached conifer wood or dark grey oakwood with a mat transparent coat.
All panels on both sides are decorated with metal frames with a brushed bonze finish.

TALASANI EASEL

Art support completely made of metal. The structure has a titanium finish whereas the shelves and the decorations have a brushed bronze finish

PERI LAMP TABLE

The structure is made of galvanized metal tube with a brushed bronze or polished nickel finish. It operates with 30W/m 3000 K° led lights, dimmable by means of a touch sensor on the base. The lamp is available in two models with different heights and lengths.

TAVERA FLOOR LAMP

The frame is made of wood with a fireproof leather upholstery and a conical lampshade is made of raw silk coupled with PVC. It operates with a low energy consumption, 30W/2700 °K dimmable light bulb. The dimmer is located on the frame. The base and the decorative elements are made of galvanized metal with a brushed bronze finish.

CAURO FLOOR LAMP

Lamp completely made of galvanized metal with brushed bronze finish and a double cylindrical lamp shade made of Basaltex coupled with white PVC. It requires  low energy consumption 7W/2700°K light bulbs, dimmable by means of a metal rod with a decorative Murano glass sphere.